BirthME, Doulas

Search for culms that are cut as low to the ground as possible. or burning away the material with a hot poker .

This simple concept is the reason why many versions of this instrument have been developed all over the world, from a traditional bamboo Antara in the Andes, to the cane Syrinx in ancient Greece, and even the wooden pipes of viking origin. I've also applied the knowledge in the book to make my own unique instruments and musical scales!

"Just the simplicity of the directions helped. 10 Tasks For Your Winter Garden My flute isn't producing a sharp sound at all. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. Then, drill consecutive holes farther down the bamboo for fingers holes that allow you to play different notes. Now, purse your lips just a bit and blow a stream of air across, and slightly into, the cavity.If you don't get a note, rotate the flute so you'll be blowing at a slightly different angle, and try again: You may have to experiment awhile to get it right (a certain amount of perseverance and breath control are required), but if you've followed my instructions correctly, you should eventually be able to make a sound. )The result will be a two-section tube that's open at the thinner end and closed at the other extremity by that joint's dividing membrane. Then add the optional holes to your flute when you've reached the point where you can make good use of the extra notes. where the hell am i suppose to get a bamboo trees in north europe????? Click twice to enlarge. You may also use the Bill Me option and pay $17.95 for 6 issues. Wasn't any hubbub that wasn't necessary. 8 years ago

on . Very true. (Some kinds of bamboo have ridge creases running lengthwise. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. This image is not<\/b> licensed under the Creative Commons license applied to text content and some other images posted to the wikiHow website. The tube's inside diameter should be between 3/4 inches and 7/8 inches . The nodes are closer together and the bamboo is thicker at this end. I just realized this was posted years ago and I was hoping there were and still videos out there somewhere. With the proper maintenance, the flute should last indefinitely.

Choose a section of bamboo with joints that are a little bit more than half as far apart as the intended length of the instrument. I want to tell you that making flutes has been a remarkable spiritual journey for me and flute making was the completion of an important phase of my journey.When I first got interested in bamboo flutes I almost gave up because I could not find any reliable information. First, use a hand saw (or coping saw or similar) to make a perpendicular cut about 1/2 – 3/4 inch from the open end. It didn't take me long to discover that fabricating a tube with holes that would make noise when I blew into it was fairly easy. You can change the pitch by covering some of the holes on the flute with your fingers and then blowing in the top hole.

If it shifts while you’re cutting it, you could accidentally injure yourself or cut a secure of the bamboo that you didn’t intend to cut.Be careful when you’re cutting with the hacksaw. I'm really enjoying the book and looking forward to trying the native American flute.A complete guide for anyone who plays the flute or ever wanted to.

. So I bought Marek's step by step guide on How to make your own Bamboo Flutes.

Diagram: Bamboo flute finger hole spacing chart. and that the one on the joint's wider end is always somewhat "sharper"—in other words, narrower—than the other. wikiHow, Inc. is the copyright holder of this image under U.S. and international copyright laws. How to Make a Bamboo Flute Bamboo has long been used by indigenous cultures to make everything from tiki huts to watermills. 8 years ago The different flute models covered in the book are Side Blown Flute, Shakuhachi, Native American Flute Bamboo Recorder and the Bamboo Sax.

To make a bamboo flute, you’ll need a drill, a rotary tool such as a Dremel, and attachments for it. This article has been viewed 264,789 times.

The interior "bulkhead" at the middle node will also still be intact. You’ll also need a general purpose hand-held sander, masking tape, a saw, a ruler or measuring tape, and a box cutter or sharp knife. The distance of the embouchure hole is approximately equal to the diameter of the flute.