They come with a safety cap to prevent leakage. If you are using UV resin, hold the pieces together and cure it under the light/lamp.
Make sure you don’t fill it up all the way otherwise your glitter/sequins inside will not move around and it will leak!10) Close your charm with the tiny resin piece that is left. Next, turn on a hair dryer and hold it 4 inches above the resin to remove any air bubbles. The next morning the film slid and it was a mess.
Add to Cart ... miniature, rhinestones, baby oil / water / water + glue / liquid (if you want to make waterfall effect) or anything colorful, kawaii, sparkle. I am back with another DIY project today and this time it is for a resin shaker charm! The discount code will be emailed to you an hour or so after you have signed up.NB. If you are unsure if a mold is backed or not, as the artist or distributor. Fill the main part with your colored resin and the other with just clear resin. Flexible, resistant to tearing. Apply a thin layer of UV resin to the outer edges of the finished piece of resin and apply the film over the top. I used a UV lamp that people normally use for gel nails and kept it under there for a couple minutes. I mean who doesn’t like watching things float around in oil. To make the process easier I transferred the oil into a small dish and used that pour the oil into the shaker. If you don’t know what that is, it is basically like a mini snow globe but it can be used as an accessory (ex. *You can use UV resin or epoxy resin with this mold.
Kawaii heart resin shaker mold. You will need to push down and turn the cap in order to open it. Secondly, connect the 2 parts carefully with epoxy or UV resin and then wait for it to fully cure before filling it with the shaker oil … If you need us urgently, please send an email and/or leave a message.© Copyright 2020 Resin8 Craft Supplies Ltd All rights reserved
I mixed some chalk and fine glitter in with my resin using a popsicle stick and aluminum dish (you can use a paper cup instead).3) There are two pieces to the mold, one is the front piece and the other is the back/main part.
If you have a syringe or pipet, you should use that too! Easy to use and clean. If you are using 2 Part resin, place something slightly heavier atop the two pieces and allow it to dry overnight.7) When the two parts are connected, add a thin layer of resin around all the edges of where the two pieces meets and let that cure. Then take your clear tape and cover the front and back of your photo.
If it’s not, continue to let it cure.
Perfect to make shaker charm, waterfall charm by adding glitter, confetti, embellishments, floating charms, rhinestones, baby oil (if you want to make waterfall effect) or anything colorful, kawaii, sparkle! These are upgraded food grade oil which is meant for crafting with shakers. Warming the resin and catalyst in this manner makes it easier to mix the two components smoothly. Remember to blow out/pop any air bubbles (you can google for more details and tips on how to get rid of air bubbles).4) If you are using UV resin, cure it under a UV lamp or with sunlight. Read our This is the front piece so I added clear resin with a bit of glitterGreen piece is main part, clear piece is front of shakerThis is the small piece you use to close the opening MiniatureSweet | Kawaii Resin Crafts | Decoden Cabochons Supplies | Jewelry MakingHeart Shaker Charm Mold | Liquid Resin Shaker Making | Waterfall Cabochon Mold | Clear Silicone Mould | Kawaii Craft Supplies (57mm x 47mm)Heart Shaker Charm Mold | Liquid Resin Shaker Making | Waterfall Cabochon Mold | Clear Silicone Mould | Kawaii Craft Supplies (57mm x 47mm)
Add your choice of embellishments inside the shaker! Perfect to make shaker charm, waterfall charm by adding glitter, confetti, embellishments, floating charms, rhinestones, baby oil (if you want to make waterfall effect) or anything colorful, kawaii, sparkle!