For a complete description of the factory-default settings, see Backup images saved on your Firebox are removed when you reset it to factory-default settings.

The status of the feature key after a Firebox reset depends on the device model:For XTM devices that have an LCD display on the front panelThe previously installed feature key is not removed when the device is started in safe mode.
For some XTM 2 Series devices, the Attn indicator does not flash.The Firebox restarts with factory-default settings. You must complete the second reboot at the end to restart your device before you can connect to it. 1 - Power off the device 2 - Held the reset button and power on the device. Before you reset a Firebox, we recommend that you export a recent backup image from the Firebox.

If you are unable to connect to a WatchGuard AP100, AP102, AP200, or AP300 after a reset, the AP might be in Failsafe mode. The Attn light not blink.

For Firebox and XTM models that do not have an LCD screen The previously installed feature key is removed. When you reset an AP to factory default settings, you must discover and pair the AP again. Make sure that you complete all of the steps.

If you want to reset the Firebox and do not want to remove the saved backup images, use the CLI command restore factory-default without the all parameter.

To reset the device to factory-default settings, power cycle the device (remove the power cable and For more information, see Make sure that you complete all of the steps. Reset Steps by Device Model. Note: You cannot reset an AP managed by WatchGuard Wi-Fi Cloud from the Wi-Fi Cloud user interface.

For more information, see When an XTM device is started in safe mode, the LCD display shows the model number followed by the word To restore a FireboxV or XTMv VM (virtual machine), you must run the Fireware CLI After you restore the factory-default settings, you can connect your computer to interface 1 and use the Quick Setup Wizard or Web Setup Wizard to create a basic configuration or restore a saved backup image.For video tutorials that show how to reset many Firebox models, see the You must use a paper clip or other small object to press the reset button through the small hole on the back of the device. In failsafe mode, the AP radios automatically broadcast these SSIDs: Radio 1 (2.4 GHz channel) broadcasts the SSID WG-Failsafe_2.4G 4 WatchGuard AP320 Hardware Specifications Reset Button Resets the WatchGuard AP device to factory-default settings. Press the down arrow on the device front panel while you power on the Firebox or XTM device. For some XTM 2 Series devices, the Attn indicator does not flash.The Firebox restarts with factory-default settings. After 40 seconds, the Arm indicator starts to flash green.The Firebox restarts with factory-default settings. For more information, see Before you reset a Firebox M5600, make sure you have an interface module installed in slot A. The Firebox restarts with factory-default settings. You must use a paper clip or other small object to press the reset button through the small hole on the back of the device. Automatically deployed APs are reset to factory-default settings if you disable the Automatic Deployment feature. If the power to a WatchGuard AP100, AP102, AP200, or AP300 is interrupted during a firmware upgrade, the firmware image could be damaged. To reset the device to factory-default settings, power cycle the device … For an AP device that uses AP device firmware 1.2.9.1 or lower The WatchGuard AP100 or AP200 device must be managed by a WatchGuard XTM device that uses Fireware ... To reboot the device, but not reset it to factory-default settings, press the reset button briefly (less than 5 seconds).

You must use the reset button on the AP.

and not ping 10.0.1.1. I ran the watchguard quick set up wizard to configure IP and then used my saved configuration files. This might be the same as my x750e I had to reset to factory settings a couple weeks ago because it lost its IP.
You can use any of these methods to reset a WatchGuard AP to factory-default settings:When you reset an AP to factory default settings, you must discover and pair the AP againIf you are unable to connect to a WatchGuard AP100, AP102, AP200, or AP300 after a reset, the AP might be in Failsafe mode. For more information, see The reset procedure you can choose depends on the firmware version on your AP or your AP model.When you unpair an AP from a Firebox, the AP restarts with factory-default settings. If you press the reset button briefly and then release the button (less than 5 seconds), the AP reboots, but it is not reset to factory-default settings. You must complete the second reboot at the end to restart your device before you can connect to it. You can reset a WatchGuard AP to factory default settings with the reset button on the AP, or you can reset the AP from the Gateway Wireless Controller on a Firebox.

If this happens, the AP starts in failsafe mode. The Firebox restarts with factory-default settings.

I lost connection with my T30 and tryed reset the box. Reset Button Resets the WatchGuard AP device to factory-default settings.

Die BOC IT-Security GmbH ist einer von vier offiziellen WatchGuard Certified Training Partnern (WCTP) in Deutschland.

The IP address of the trusted interface changes to 10.0.1.1. Power off the Firebox or XTM device.



For some XTM 33 devices, the Attn indicator does not flash.The Firebox restarts with factory-default settings. tryed plug the cable in the port 1/LAN and device dont give me the ip 10.0.1.x.