The closer the value is to 0, the stronger the signal. For more information on signal strength, see Do not enable Fast Handover on adjacent APs that also have the Band Steering feature enabled. In the Syslog server IP address text box, type the IP address of your syslog server. The default value is -85 dBm. Whether you are looking for a quick answer, technical training on how to use your products, or you need assistance from one of our experts, you can get started here. SHA1 f09a36b7406eaa70a50f2f5262364872e88c7ff5 WatchGuard’s integrated wireless controller technology combined with WatchGuard’s AP100, AP102, AP200, and AP300 wireless access points allows users to easily apply security policies to wired and WLAN resources simultaneously , which is critical to enforcing security standards across the entire network infrastructure. The minimum is -100 dBm and the maximum is -60 dBm.

Das beabsichtigte End-of-Sale (EOS) Datum wird meist schon im Voraus angekündigt. The only way to update your AP devices to v1.2.9.6 is through Gateway Wireless Controller. You cannot change the configuration of an AP if it is located behind a router or other network device and cannot receive broadcasts from the Gateway Wireless Controller. From the Gateway Wireless Controller on your Firebox, you can edit the settings for any APs that are paired with the Firebox. (Fireware v12.0.2 or lower) To help wireless clients that roam between WatchGuard APs connect to another AP with a stronger signal, select the This is also the threshold for when a client should disconnect from this AP and connect to another AP with a stronger RSSI level (AP300 devices only). WatchGuard End-of-Life (EOL) Richtlinie Wenn ein WatchGuard Modell oder ein Subscription Service aus dem aktiven Verkauf genommen werden soll, stellt WatchGuard rechtzeitig entsprechende Informationen bereit. Solange noch Hardware Ware verfügbar ist, kann diese auch noch bestellt werden. Steering to the 5 GHz band can result in a loss of RSSI strength for the client and can cause disconnections based on the Fast Handover threshold. My WatchGuard For more information, see Do not use Band Steering and Fast Handover features at the same time. The Gateway Wireless Controller dialog box appears.The list of Access Points that you can configure appear in the Paired Access Points list.The Gateway Wireless Controller dialog box appears.The list of Access Points that you can configure appear in the Access Points list.The default name is _. The value is expressed in dBm (decibel milliwatts). WatchGuard AP200 - wireless access point - with 3 years LiveSecurity Service overview and full product specs on CNET. The 5 GHz band provides greater performance than the 2.4 GHz band, but is not compatible with all wireless devices. Released 01/07/2016 While the update is in progress, the AP status briefly changes to These AP steering parameters enable you to configure thresholds and other advanced parameters for the You can configure different thresholds for specific APs. For information on how you can flash the power LED to help identify APs in stealth mode, see If you configure a communication VLAN ID in both the Gateway Wireless Controller settings and the AP settings, the Firebox uses the communication VLAN ID specified in the AP settings.When you save an AP configuration to the Firebox, the device immediately sends the update to the affected APs. Fireware v11.10.5 includes new AP firmware v1.2.9.6 for AP100/102 and AP200 devices. (Fireware v12.0.2 or lower) To help wireless clients that roam between WatchGuard APs connect to another AP with a stronger signal, select the Fast Handover check box. WatchGuard Schulungen.

This AP firmware is the same version included with Fireware v11.11. Set the Band and Wireless Mode.

Fast Handover controls the minimum signal strength required to associate with an AP and tells wireless clients when to release their current AP association if the signal degrades as the wireless client moves farther away.In Fireware v12.1 or higher, Fast Handover is replaced by the Min.

Die BOC IT-Security GmbH ist einer von vier offiziellen WatchGuard Certified Training Partnern (WCTP) in Deutschland. For more information, see (Fireware v12.0.2 or lower) To move dual-band wireless clients from the 2.4 GHz band to 5 GHz, select the On AP100, AP102, AP200, and AP300 devices, this option allows you to operate your AP in stealth mode to hide visible signs of wireless activity when the device is deployed in a location that requires additional security. For more information, see When you pair an AP with a Firebox, you must configure the settings for the AP. External syslog support is only available for AP100, AP102, AP200, and AP300. For more information, see Fast Handover uses the RSSI (Received Signal Strength Indicator) as a threshold to determine if clients can associate to an AP and when to disconnect a wireless client with a weak signal. WatchGuard’s integrated wireless controller technology combined with WatchGuard’s AP100, AP102, AP200, and AP300 wireless access points allows users to easily apply security policies to wired and WLAN resources simultaneously , which is critical to enforcing security standards across the entire network infrastructure.

Association RSSI and Smart Steering options configured in the SSID settings. AP firmware v1.2.9.6 is not available in the Software Downloads Center. Band Steering is usually not required in an environment where most wireless devices are newer devices that are already optimized to choose the 5 Ghz band.In Fireware v12.1 or higher, Band Steering is configured in the SSID settings. The model and serial number are automatically set for paired APs and cannot be changed.There are two network settings you can select for an AP:Select this option to assign the AP a static IP address.

WatchGuard APs support two wireless frequency bands: 2.4 GHz and 5 GHz. When you select XTM devices from one place – reducing both setup time and maintenance costs.